MCQs on Lathe-3

1 - Question

Which of the following can be effectively used for holding eccentric job?
a) Four jaw chuck
b) Three jaw chuck
c) Both three jaw chuck and four jaw chuck
d) Two jaw chuck
View Answer Answer: a
Explanation: Four jaw chucks are used for holding eccentric job because of good manual balancing capability of four jaws.



2 - Question

Which of the following can be effectively used for holding irregular job?
a) Four jaw chuck
b) Three jaw chuck
c) Both three jaw chuck and four jaw chuck
d) Two jaw chuck
View Answer Answer: a
Explanation: Four jaw chucks are used for holding irregular job because of good manual balancing capability of four jaws.



3 - Question

Which of the following is also known as universal chuck?
a) Four jaw chuck
b) Three jaw chuck
c) Both three jaw chuck and four jaw chuck
d) Two jaw chuck
View Answer Answer: a
Explanation: Four jaw chucks are used for holding eccentric job as well as irregular job apart from holding symmetric job because of good manual balancing capability of four jaws. advertisement



4 - Question

Which of the following is mostly used for holding bored part of the job?
a) Mandrels
b) Dogs
c) Collet
d) Angle plate
View Answer Answer: a
Explanation: Mandrels are used to hold bored job during machining process of jobs.



5 - Question

What will be the value of half taper angle in degrees if diameter of big end is 100mm and diameter of small end is 60mm for a 1m long job?
a) 3.19
b) 5.29
c) 1.14
d) 2.29
View Answer Answer: c
Explanation: Half angle can be calculated by using- tan (half taper angle) = (D-d)/ (2*L).



6 - Question

What will be the value of half taper angle in degrees if diameter of big end is 500mm and diameter of small end is 60mm for a 1m long job?
a) 31.10
b) 52.30
c) 31.10
d) 12.40
View Answer Answer: d
Explanation: Half angle can be calculated using- tan (half taper angle) = (D-d)/ (2*L).



7 - Question

What will be the value of diameter of big end in mm for tapered job if diameter of small end and length of job is 60mm and 1m respectively? Given half taper angle is equal to 12.4 degrees.
a) 600
b) 500
c) 400
d) 300
View Answer Answer: b
Explanation: Big end diameter can be calculated using- tan (half taper angle) = (D-d)/ (2*L).



8 - Question

What will be the value of diameter of small end in mm for tapered job if diameter of big end and length of job is 60mm and 1m respectively? Given half taper angle is equal to 1.14 degrees.
a) 600
b) 200
c) 100
d) 300
View Answer Answer: c
Explanation: Small end diameter can be calculated using- tan (half taper angle) = (D-d)/ (2*L).



9 - Question

During taper turning operation 100mm of smaller side diameter and 800mm of bigger side diameter was required. What will be the value of taper gradient for a job of 1m in length?
a) 15.01
b) 19.29
c) 28.35
d) 56.31
View Answer Answer: b
Explanation: Taper gradient= tan (half taper angle) = (D-d)/ (2*L).



10 - Question

During taper turning operation 100mm of smaller side diameter and 800mm of bigger side diameter was required. What will be the value of Conicity for a job of 1m in length?
a) 31.20
b) 23.20
c) 56.32
d) 38.58
View Answer Answer: d
Explanation: Conicity=2* tan (half taper angle) = (D-d)/ (*L).

Get weekly updates about new MCQs and other posts by joining 18000+ community of active learners