# Heat Transfer MCQ’s – Heat Generation Through Plane Wall

1 - Question

In case of heat conduction through the plane wall, which one of the following is not a correct assumption?
b) Three dimensional heat flow
c) Volumetric heat generation must be constant
d) K must be constant
Explanation: There should be two dimensional heat flow. The differential equation describing the temperature distribution can be set up by making an energy balance.

2 - Question

If Q X is heat generated in at distance ‘x’, then heat conducted out at a distance (x + d x) will be
a) Q X + 3d (Q X) d x /d x
b) 2Q X + d (Q X) d x /d x
c) d (Q X) d x /d x
d) Q X + d (Q X) d x /d x
Explanation: Q X + Q g = Q X + d X.

3 - Question

Notable example of uniform generation of heat within the conducting medium are (i) Energy of a nuclear reactor (ii) Liberation of energy due to some exothermic chemical reactions (iii) Resistance heating in electrical appliances Which of the statements made above are correct?
a) i, ii and iii
b) i and ii
c) i and iii
d) Only ii
Explanation: All the statements are correct with respect to plane wall heat conduction.

4 - Question

For a plane wall of thickness l with uniformly distributed heat generation q g per unit volume, the temperature t 0 at mid plane is given by
a) t 0 = q g l 2/2k +t w
b) t 0 = q g l 2/4k +t w
c) t 0 = q g l 2/8k +t w
d) t 0 = q g l 2/16k +t w
Explanation: t = q g /2k (l – x) x + t w. At mid plane i.e. x = l/2 we get t 0 = q g l 2/8k +t w.

5 - Question

The temperature drop in a plane wall with uniformly distributed heat generation can be decreased by reducing
a) Wall thickness
b) Heat generation rate
c) Thermal conductivity
d) Surface area
Explanation: On decreasing wall thickness, generally temperature drop decreases.

6 - Question

Consider a slab of thickness δ with one side (x = 0) insulated and other side (x = δ) maintained at constant temperature. The rate of uniform heat generation within the slab is q g W/m3. Presuming that the heat conduction is in steady state and one dimensional along x direction, the maximum temperature in the slab would occur at x equal
a) δ/2
b) Zero
c) δ/4
d) δ
Explanation: Maximum temperature occurs at the insulated face of the wall where x = 0.

7 - Question

There occurs heat conduction and internal heat generation at uniform rate within the conduction medium itself in the following cases (i) Drying of concrete (ii) Chemical processes (iii) Fuel elements in a nuclear reaction Choose the correct option
a) i only
b) ii only
c) i and iii
d) i, ii and iii
Explanation: All are correct as there is heat conduction in all above cases. The rate of heat generation has to be controlled one, otherwise the resulting temperature growth might result in the failure of the medium

8 - Question

The rear window of an automobile is made of thick glass i.e. AB = 5 mm and thermal conductivity is 0.8 W/m degree. To defrost this window, a thin transparent film type heating element has been fixed to its inner surface. For the conditions given below, determine the electric power that must be provided per unit area of window if a temperature 5 degree Celsius is maintained at its outer surface. Interior air temperature and the corresponding surface coefficient are 20 degree Celsius and 12 W/m2 degree. Surrounding air temperature and the corresponding surface coefficient are – 15 degree Celsius and 70 W/m2 degree. Electric heater provides uniform heat flux

a) 232.5 /m2
b) 1232.5 /m2
c) 2232.5 /m2
d) 3232.5 /m2

Explanation: (t I – t f)/(1/h i + δ/k) + q g = h 0 (t s – t 0).

9 - Question

Suppose heat is conducted due to electrons Where, i = I/A and p is the resistivity, then
) q g = 2i2 p
b) q g = 3i2 p
c) q g = i2 p
d) q g = 4i2 p
Explanation: It should be i2 p. Here i is current density.

10 - Question

In case when both the surfaces of plane wall are at different temperature, we get an expression i.e. T MAX – T W2 /T W1 – TW2 = (B + 1)2/4B What is the value of B?
a) (q g) (δ)2/2k (T W1 – TW2)
b) (q g) (δ)3/3k (T W1 – TW2)
c) (q g) (δ)4/4k (T W1 – TW2)
d) (q g) (δ)5/5k (T W1 – TW2)