Aircraft Design MCQ – Airfoil Selection-1
1 - Question
The parameter marked by ’?’ in the diagram is _____
a) trailing edge
b) leading edge
c) chord
d) camber
View Answer
Explanation: The diagram is showing typical airfoil shape. The trailing edge of an airfoil is end point of the airfoil. It is most after portion of the airfoil as shown in the diagram. Leading edge in contrast, is foremost part of an airfoil.
2 - Question
The cross-sectional shape of wing is called _____
a) airfoil
b) circle
c) camber
d) chord
View Answer
Explanation: Wings are designed with airfoil cross-section. Engine inlets are typically circular in cross-sections. Camber and chord are parameters of an airfoil.
3 - Question
Aerofoil affects the performance parameters of aircraft.
a) True
b) False
View Answer
Explanation: Airfoil is cross-section of the wing. Airfoil will affect lift, drag, take-off characteristics etc. In general, crucial performance parameters are affected by airfoil selection.
4 - Question
Which of the following is correct?
a) Lift produced by an airfoil is always equal to weight
b) Drag by sphere is more than the drag produced by an airfoil for similar conditions
c) Drag by sphere is less than that of produced by an airfoil for similar conditions
d) Drag by sphere is equal to the drag produced by an airfoil for similar conditions
View Answer
Explanation: Lift produced is not always same as weight. Sphere is a 3D object. Drag produced by sphere will be more due to increased friction and 3D effects. An airfoil is 2D shape which will have less drag as compare to sphere for all similar conditions.
5 - Question
An aerofoil is operating with flow velocity of 100m/s. Aerofoil is symmetric and is at 0° AOA. Determine lift produced by this aerofoil.
a) 10.5 N
b) 0 N
c) 50 N
d) 100N
View Answer
Explanation: Lift is an upward force produced by pressure difference. Given, velocity V=100m/s, AOA = 0°. For symmetric airfoil at 0° AOA pressure will be same as upper and lower surface. Hence, lift = 0N.
6 - Question
Which of the following is not type of an airfoil?
a) Symmetric
b) Camber
c) Whitcomb
d) Vortex
View Answer
Explanation: Symmetric airfoils have symmetric curvature at both side. Camber are non-symmetric airfoils. Whitcomb is also type of airfoil. Vortex is a phenomena, not the type of an airfoil.
7 - Question
Airfoil is a streamline shape.
a) True
b) False
View Answer
Explanation: Streamline shape is that shape which gives streamlined flow. An airfoil has that characteristic. An airfoil is able to provide much smoother flow than non-streamlined body.
8 - Question
A symmetric airfoil is operating with flow velocity of 350m/s. The lift produced by the airfoil is 21 N at 0.008 rad AOA. If chord is c m then, what will be the pressure difference across the airfoil?
a) 21/c Pa
b) 21c/2 N
c) 21 Pa
d) 21c N
View Answer
Explanation: Given, symmetric airfoil Flow velocity V=350m/s, Lift L=21N, AOA = 0.008rad Chord = c m, Span of airfoil = 1 unit Pressure difference = Lift/Area of airfoil = 21/c*1 = 21/c Pa.
9 - Question
If an airfoil has lift of 200 N at 10° AOA, then what is induced drag produced by airfoil at that AOA?
a) 0 N
b) 100
c) 0
d) 100 N
View Answer
Explanation: Given, Lift=200N, AOA = 10° Here, airfoil is mentioned which is 2D shape. For an airfoil Induced drag Di = 0N.
10 - Question
Find location of aerodynamic centre from leading edge if, chord is 10m and airfoil has flow velocity of 0.2 M.
a) 2.5 m
b) 0.2 m
c) 5 m
d) 10 m
View Answer
Explanation: Given, velocity = 0.2M = 0.2*340 = 68m/s Chord = 10m Given velocity is less than the sonic speed. Hence, location of aerodynamic center is = 25% of chord = 0.25*10 = 2.5m from leading edge.
11 - Question
Consider a NACA 2812 airfoil. It is operating with flow velocity of 900m/s with chord of 1m. What should be the maximum thickness of this airfoil?
a) 0.12m
b) 0.21m
c) 0.9m
d) 28.12m
View Answer
Explanation: NACA-4 digit series is used to define certain airfoil characteristics. Here, velocity = 900 m/s, chord = 1m From NACA-4 digit, Maximum thickness = last two digits in percent of chord=12% of chord = 0.12*1 = 0.12m.
12 - Question
An airfoil is subjected to the flow with temperature of 288.16K and flow is ideal. The velocity at the leading edge is ____
a) 0m/s
b) 250m/s
c) 288.16m/s
d) 16.882m/s
View Answer
Explanation: Given, temperature T=288.16K For idle flow, at leading edge flow is brought to rest isentropically. Hence, velocity at leading edge = velocity of flow at the impact to leading edge = 0m/s.
13 - Question
Pitching moment co-efficient for an airfoil is given by _____
a) lift*area
b) drag*area
c) section pitching moment/dynamic pitching moment
d) lift/dynamic moment
View Answer
Explanation: Lift*area will give moment. Drag*area will also provide moment but will be less. The ratio of sectional pitching moment and dynamic pitching moment is called pitching moment co-efficient.
14 - Question
Which of these is not part of an airfoil?
a) Leading edge
b) Chord
c) Camber
d) Fins
View Answer
Explanation: Fins are extended surfaces which are used to improve heat transfer. Leading edge is foremost part of an airfoil. Camber is curve of an airfoil.
15 - Question
We are using the airfoil in the aircraft as _____
a) it is a streamline shape which provides better aerodynamics
b) it is a random shape can be changed to rectangular as well
c) it is easy to make than rectangular
d) it is not a streamline body
View Answer
Explanation: Airfoil is a streamlined body which provides much smoother flow than non-streamlined body. Airfoil is designed in such a way that it can provide better aerodynamics than any other shape. Hence, in aircraft we use airfoils.